Geelang LIGO78X for GOPRO 2 Inch 78mm 4S Cinewhoop FPV Racing Drone PNP/BNF w/ Naked Camera Mount F4 FC 13A ESC GL1204 5000KV Motor

(2 customer reviews)


Geelang LIGO78X for GOPRO 2 Inch 78mm 4S Cinewhoop FPV Racing Drone PNP/BNF w/ Naked Camera Mount F4 FC 13A ESC GL1204 5000KV Motor

DSMXWithout Receiver


Note: The camera for Gopro shown in the photo is not included. Only included camera mount .


Brand Name: GEELANG

Mode Name: LIGO78X GOPRO

Item Name: 4S 78mm Ducted Cinewhoop Drone BNF

Wheelbase: 78mm

Size: 119x132x23mm(Camera Mount Not Included)

Weight: 90g (Camera Mount Not Included)

Weight: 166g (With 4s 450 Battery, for GOPRO 6 Naked Camera )

Recommended Battery: 4s 450, 4S 550mAh Lithium Battery


Flight controller

Flight controllerSI-F4FC V1 Three-in-one tower  Version:MATEKF411

MCU:STM32F411CEU6 (100MHZ, 512K FLASH)

Sensor: MPU-6000(SPI connection)

StoreOnboard black box

Board size:21 * 21MM

Power supply: 2-4S battery input (DC 7-17V)

Built-in 12A(each) Blheli_S 4in1 ESC Dshot600 ready

Built-in Betaflight OSD(SPI Control)

Built-in Current meter Max 70A

Current meter scale set to 480

Built-in 5V 2A BEC

Built-in voltage detection

Onboard 4in1 ESC

Onboard 4in1 ESC MCU upgraded to EFM8BB21

Power supply: 2-4S LiPo/LiPo HV (7v/17v)

Current: 13A continuous peak 15A (5 seconds)

Support BLHeliSuite programmable

Factory firmware: G_H_30_REV16_77.HEX

Default protocol: DSHOT600


Motor ModeGL1204 KV5000

Stator specificationsD12 * H4 0.2mm for Kawasaki


Stator Diamter:12mm

Stator Length:4mm

Shaft Diameter:Φ1.5mm

Motor Dimension(Dia.*Len):Φ16.0mm*15.8mm

Magent specifications: N52H

Shift specifications: 2mm High strength steel

Bearing Specifications: d2*D5*H2.5 MR52zz Japan ISC Custom made

WindingSpecifications:180℃ Class Multiple oxygenfree copper


No.of Cells(Lipo)3S-4S

5.8G VTX

Power switching: third gear(25MW 、 100MW 、200MW)

Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Raceband

Smartaudio ready(Frsky EU-LBT and DSMX version not compatible) 
Weight: 2.0g


Model: Ant lite

Image Sensor: 1/3 CMOS Sensor

Horizontal Resolution : 1200 TVL

TV System: NTSC and PAL switchable

MENU: Support

IMAGE: 4:3

Synchronization: Internal

Electronic Shutter

PAL: 1/50~100,000; NTSC: 1/60~100,000

S/N Ratio: >52dB (AGC OFF)

Video Output: CVBS

Lens: 1.8mm / F2.5

FOV : 165°

Min. Illumination: 0.001Lux

Auto Gain Control: YES


WDR : Global WDR DNR


Gemfan D51 (2020-4) Cinewhoop props

Material: PC

Weight: 0.91g

Pitch: 2 inches

Prop diameter: 50.3 mm

Center thickness: 4.5mm

Center hole diameter: 1.5mm 3 holes

Receiver Version (Optional)

Frsky XM+ Non-EU

SBUS receiver
Frsky D8/D16 switchable
Compatible Non EU transmitter both D8 and D16 mode
Channels: 8ch or 16ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
Operating Voltage Range: 3.7~10V
Operating Current: 30mA @5V
Operating Range: Full range
With RSSI output on board: Analog 0~3.3V
Firmware upgrade-able, can be upgrade to EU with RSSI

Frsky AC900

Three-in-one receiver
SBUS receiver
Frsky D16 for futaba s-fhss switchable
Compatible Non EU transmitter both D16 mode
Channels: 8ch or 16ch
Failsafe support

No ground interference (Transmitter and receiver 1 m from the ground): 300m

Flysky AFHDS-2A

IBUS receiver
Protocol:  AFHDS-2A
Channels:  14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
Failsafe support


CRSF Protocol,Official TBS transmitter compatible  
Protocol: CRSF  
Channels: 8ch Failsafe support   
Support receiver hardware rssi function                                                                         

No ground interference ( Transmitter and receiver 1 m from the ground): 500m


Seria IBUS Receiver

Protocol: DSM2/DSMX Compatible

Channels: 6-9 (Depend On Your Radio)

No Ground Interference (Transmitter and Receiver 1 M from the ground): 300M

Battery Recommended

Species : lipo、lipoHV

Continuous Discharge Rate: 60C
Instantaneous discharge rate: 80C
Connector: xt30


– Adopt SIF4 1.0 flytower flight controller to support 2-4s lithium battery power supply, independent four-in-one 13a ESC. The integrated Betaflight OSD function keeps abreast of the signal of the flight voltage receiver and can observe the status in real time while flying. With 16m chip black box, it is more convenient to adjust the machine for analysis. 

– A more compact design is adopted for the first time, with a wheelbase of 78mm. However, passing long-term flight tests will not affect flight efficiency at all. The FPV end adopts CADDX ANT lite camera, the image quality is clear. The complex environment of flying indoors has better observation and controllability.

– The 4s power supply and 2-inch ducted four-blade propeller have been tested and matched for a long time and have good operability and durability. It is recommended to use 4s 450mah battery, if you need more residence time, you can add 4s550mah battery. Through continuous improvement, the problem of low efficiency of the 2-inch air duct machine was finally solved. Indoor small cross aerial photography becomes a reality. In order to better protect the outer ring, EVA sponge material is used to improve safety and reduce wind resistance. Through some modeling optimizations, the performance is very good.

– Independent use of multiple versions of the receiver, electronic control is more stable. The flight control adopts the newer version of Betaflight 4.2, and the ESC adopts the 16.77 version. Both the two-way DSHOT mode and the gyroscope RPM filter are turned on to make the flight control more stable.

– Using 1204kv5000 motor and 2020 ducted four-blade propeller 3-4s power supply, the efficiency ratio is super high. Flight control stability

– The whole machine is controlled at 90 grams, which solves the weight problem of traditional ducting machines and is flexible in control.

– Package includes gopro6/7 bare metal cover and camera mount, users do not need to purchase separately

– Compared with 3-inch and 2.5-inch air duct machines, the air duct is smaller and the flight efficiency is not affected. By installing the lightweight GOPRO bare metal, it is very suitable for professional video photographers.

Package Included:
1 x 78mm 3D Printing Combined Frame
1 x 3D Printed for GOPRO 67 Naked Camera Caset

Option1: SIF4 1.0 FC external Frsky NON-EU xm+ Receiver

Option2: SIF4 1.0 FC external DSMX receiver

Option3: SIF4 1.0 FC external Frsky AC900 Receiver(Multi-mode receiver)

Option4: SIF4 1.0 FC external TBS NANO Receiver

Option5: SIF4 1.0 FC external FLYSKY Receiver

Option6: SIF4 1.0 FC PNP NO RX Receiver

4 x GL1204 5000KV Motor
1 x 2020 Propeller(4cw+4ccw)

1 x 5.8G VTX5840

1 x GL950 Camera
1 x Screwdriver Removal Tool
1 x Battery Magic Strap
1 x USB 90°Adapter Plug

1 x Caddx Ant Lite

1 x 4s 450mAh Lihv Battery

4bfb6e50 521d 4204 a390 4bb50d0ff073 2

f9703886 2acb 45b4 86bc 7c6de5974781 2

df1751da eb66 4960 a8a4 5b30b6e3a535 2

9ab2b43f 73e1 4570 947b 334c3df30e80 2

c0482d2c 62f4 43ef 9384 163fd895d405 2

1bc60b79 9342 440d a910 ad3f4b080c0f 2

a014e659 747a 4e98 b46a 57663b66a519 2

9f8cc153 6502 4bb8 956c 296133d5bd6e 2

Additional information

Weight0.3 kg

AC900 Receiver, DSMX, Flysky AFHDS 2A receiver, Frsky XM+ Receiver, TBS Crossfire Receiver, Without Receiver

2 reviews for Geelang LIGO78X for GOPRO 2 Inch 78mm 4S Cinewhoop FPV Racing Drone PNP/BNF w/ Naked Camera Mount F4 FC 13A ESC GL1204 5000KV Motor

    April 29, 2021
    A must - have.
    March 6, 2021
    Would buy again.

Only logged in customers who have purchased this product may leave a review.